Cheapest Factory TU-1A90 thermal wax actuator for automobile thermostat for Qatar Factory
Short Description:
Product Detail
Product Tags
Cheapest Factory TU-1A90 thermal wax actuator for automobile thermostat for Qatar Factory Detail:
1. Operation Principle
The Thermostatic Wax that has been sealed in shell body induces expansion by a given temperature, and inner rubber seal part drives its handspike to move under expansion pressure to realize a transition from thermal energy into mechanical energy. The Thermostatic Wax brings an upward movement to its handspike, and automatic control of various function are realized by use of upward movement of handspike. The return of handspike is accomplished by negative load in a given returned temperature.
2. Characteristic
(1)Small body size, occupied limited space, and its size and structure may be designed in according to the location where needs to work.
(2)Temperature control is reliable and nicety
(3)No shaking and tranquilization in working condition.
(4)The element doesn’t need special maintenance.
(5)Working life is long.
3.Main Technical Parameters
(1)Handspike’s height may be confirmed by drawing and technical parameters
(2)Handspike movement is relatives to the temperature range of the element, and the effective distance range is from 1.5mm to 20 mm.
(3)Temperature control range of thermal wax actuator is between –20 ~ 230℃.
(4)Lag phenomenon is generally 1 ~ 2℃. Friction of each component part and lag of the component part temperature cause a lag phenomenon. Because there is a difference between up and down curve of traveling distance.
(5)Loading force of thermal wax actuator is difference, it depends on its’ shell size.
Product detail pictures:
abide by the contract", conforms on the market requirement, joins within the market competition by its superior quality likewise as provides far more comprehensive and great company for shoppers to let them develop into huge winner. The pursue on the corporation, is definitely the clients' gratification for Cheapest Factory TU-1A90 thermal wax actuator for automobile thermostat for Qatar Factory, The product will supply to all over the world, such as: Islamabad , Romania , kazakhstan , With the highest standards of product quality and service, our products have been exported to more than 25 countries like the USA, CANADA, GERMANY, FRANCE, UAE, Malaysia and so on.We are very pleased to serve customers from all over the world!
Water heaters: https://ali.pub/jva06
Cashback 7% Aliexpress: https://cashback.epn.bz/?inviter=4087b
Partnership program AliExpress: https://epn.bz/joinus/?inviter=4087b
What if I broke a water heater? The heater does not heat the water? How to check the heater? How to repair the water heater thermostat is not folding their hands at home?
1) Pull out the plug from the socket.
2) Remove the protective cover with a button.
3) Disconnect the thermostat terminals.
4) Remove the thermostat.
5) If you know the power of your heating element, it is possible to directly measure up its resistance. If not, will loosen and view features on the inner surface.
Resistance can be calculated using the formula:
R = U² / P, Ohm,
where U – voltage power supply (I 220);
P – power heater (1200 W I);
R = 220² / 1,200 = 40.33 ohms.
Align the multimeter to resistance measurement mode in the range of 200-2000 Ohms (my multimeter minimum limit of the measuring 2,000 ohms).
If the instrument will show a value close to the calculated, the heater is OK. In all other cases, be replaced.
To check the thermostat should be set the multimeter to continuity test mode and check the contact between each pair of terminals. If the beeps, then everything is in order. If not, then most likely it is a break contact. Turn the knob counter-clockwise and check again. Still not contact? Then the problem thermostat. Chances are oxidised, or, as in my case, the contact “rocker” become attached to the plastic.
To disassemble the thermostat is necessary to pull up the knob and then unscrew it, then drill out rivets. Slowly disconnect the 2 halves. The smallest detail – a spring. Watch out for it! 
If the pad is in the top position, try to click on it, it should come back. Then only need to clean the contacts.
ATTENTION!!!
In my case it was necessary to enclose a piece of adhesive tape. In my opinion it was the easiest and most affordable option. Perhaps you could apply a thin layer of hot glue. THIS IS ONLY MY EXPERIENCE AND DO NOT RECOMMEND DO AS I DO !!!
To assemble the need to find 2 screw and 2 nuts.
I share all that I am doing own hands at home. The channel you will see homemade, crafts, repair of equipment, experiments, tests, unpacking and review products from China (Aliexpress), various household manual. I also will share my inventions and interesting ideas to improve and simplify the life (life hacking).
Movies shown on that channel, show the personal experience and are entertaining. For all that you do, you answer yourself. Observe caution and safety rules.
///////////////// SUBSCRIBE \\\\\\\\
********** https://goo.gl/Tp0aX9 ***********
////////////////////////////////////////////////
////////////// MY CHANNELS \\\\\\\
https://goo.gl/LWSVj3 – Live Laugh
https://goo.gl/GLJ2hf – Alexander Dikovinniy
https://goo.gl/IlJ8ZE – Dikovinniy World
https://goo.gl/2mqicP – Animals and Fun
**************** PLAYLISTS ****************
goo.gl/lTXljH – Instuctions
goo.gl/Jy8Xjd – Parcels, Reviews, Tests
goo.gl/RtQfXg – Water Device
goo.gl/u4Snhv – Interesting Ideas
goo.gl/LzpXou – Repairs
goo.gl/lzM9Yg – Toyota Camry Gracia
goo.gl/zOHwUB – The use of plastic PET bottles DIY
**********************************************
Music:
Pisco_Sour
Making_Rounds
/////////////////= HELP CHANNEL =/////////////////
PayPal: Dikovinniy@yandex.ru
Webmoney (WMZ-dollars): Z315805724463
how to temporary fix your original washer parts that leaves clothing wet and will not run on final spin.
