Cheap PriceList for TU-1K01 thermal wax actuator for electric switch valve to Japan Manufacturer
Short Description:
Product Detail
Product Tags
Cheap PriceList for TU-1K01 thermal wax actuator for electric switch valve to Japan Manufacturer Detail:
1. Operation Principle
The Thermostatic Wax that has been sealed in shell body induces expansion by a given temperature, and inner rubber seal part drives its handspike to move under expansion pressure to realize a transition from thermal energy into mechanical energy. The Thermostatic Wax brings an upward movement to its handspike, and automatic control of various function are realized by use of upward movement of handspike. The return of handspike is accomplished by negative load in a given returned temperature.
2. Characteristic
(1)Small body size, occupied limited space, and its size and structure may be designed in according to the location where needs to work.
(2)Temperature control is reliable and nicety
(3)No shaking and tranquilization in working condition.
(4)The element doesn’t need special maintenance.
(5)Working life is long.
3.Main Technical Parameters
(1)Handspike’s height may be confirmed by drawing and technical parameters
(2)Handspike movement is relatives to the temperature range of the element, and the effective distance range is from 1.5mm to 20 mm.
(3)Temperature control range of thermal wax actuator is between –20 ~ 230℃.
(4)Lag phenomenon is generally 1 ~ 2℃. Friction of each component part and lag of the component part temperature cause a lag phenomenon. Because there is a difference between up and down curve of traveling distance.
(5)Loading force of thermal wax actuator is difference, it depends on its’ shell size.
Product detail pictures:
To be a result of ours specialty and repair consciousness, our corporation has won a good popularity amid consumers everywhere in the environment for Cheap PriceList for TU-1K01 thermal wax actuator for electric switch valve to Japan Manufacturer, The product will supply to all over the world, such as: America , Austria , Mauritania , We always insist on the management tenet of "Quality is First, Technology is Basis, Honesty and Innovation".We are able to develop new products continuously to a higher level to satisfy different needs of customers.
An introduction to Polypipe’s Smart Plus Temperature Controls
Did you know, an electric water heater can account for up to 25% of a home’s energy bill? The United States Department of Energy recommends setting a residential water heater to 120ᵒ F to reduce energy usage and to help prevent scalding. Each 10ᵒ F reduction in water temperature can save 3% – 5% on an energy bill. Save energy and help make the home safer by reducing the thermostat setting on residential water heaters.
Justin Holzgrove, PUD 3 Conservation Manager, demonstrates how to check and adjust water heater temperature in this video.
To Check and Adjust Water Heater Temperature:
TOOLS NEEDED: a flat head screwdriver and a regular home cooking thermometer.
1. Turn on the hot water at the faucet CLOSEST to the water heater. This may be in a bathroom, laundry room, kitchen, etc. Let it run for at least three minutes to ensure water is coming directly from the water heater tank.
2. Measure the water temperature using the cooking thermometer. It may be easier to place a small cup below the faucet.
3. Turn off the water heater breaker at the home’s electric panel. This should be done prior to making any adjustments.
4. Locate the water heater access panels. Many water heaters have a top and bottom element. Both should be adjusted to the same temperature.
5. Remove the water heater access panel. Insulation may need to be removed to access the thermostat. If so, consider wearing gloves. Do not remove the plastic cover on the thermostat.
6. Using the flat head screwdriver, adjust the temperature down to 120ᵒ F. The thermostat may not have the setting in degrees. Instead it may use terms such as “HOT” and “COLD”. Adjust accordingly.
7. Replace the access panels and turn on the circuit breaker to re-energize the water heater.
8. Wait three hours before testing again to allow changes to take effect.
9. Re-measure the water temperature.
Washington State law (RCW 19.27A.060) requires that new residential water heaters sold in the state be pre-set at 120ᵒ F. Mason County PUD No. 3 is required to notify customers annually that state law recommends their water heaters should be set no higher than 120ᵒ F. Furthermore, when a home is sold or rented, the previous owners or agent must set the water heater back to 120ᵒ F before the next resident’s occupancy.
From a safety and cost-savings standpoint, lowering the temperature makes a lot of sense.
Temperature of water in relation to the time it takes to cause a bad burn:
150°F (66°C) – 2 SECONDS
140°F (60°C) – 6 seconds
125°F (52°C) – 2 minutes
120°F (49°C) – 10 MINUTES
For Questions or Comments, please contact the Mason County PUD No. 3 Conservation Department at (360) 426-0777 or email web@masonpud3.org
